福力德濾油車LUC-16*3,LUC-16*5,LUC-16*10精細濾油小車

LUC系列精細濾油車

一、簡介

INTRODUCTION

該濾油車是- -種可移動式的濾油裝置，有16、 40、63、100、 125五種流量規格。適用于液壓、潤滑系統灌注新油、分裝儲運時的過濾或用于設備保養的過濾，亦可用于臟油的回收等。

該濾油車是由電動機、油泵、濾油器等組成，只須將濾油車上的吸油管、出油管插入被過濾設備的油箱中，開動電動機，使存油經濾油車循環過濾，從而提商油箱中(即系統)存油的清潔度，而且在過濾過程中系統仍可照常工作。

This filter vehicle is am ovable filter device, and it has five flov rate norms; 16,40.63.100,125 it is applied to filteting at hydr aulic sytem, lubrication saystem new oil filing, a the filter of system m aintenance. eand alsothereuse of darty oil.

This fiter vehcle 18 comprise of ele ctromotor, oil pump. filter and so on Ifw e want the filter vehclecir culatly lubricate the oil in the tank, we only need to insert the intake tube and outlet tube into the tank of filter systen, then start the elect oam otor. Thus can not only im p ove the clearing degree of oil in the tank, butalso the ytem can work norm alyy

LUC精細濾油車特點：

1.結構緊湊，體積小，重量輕，移動方便，運行平穩，無噪聲，使用維護方便；

2.用途廣泛適用于液壓油，汽輪機油，潤滑油，切削液等廣大油品；

3.粗濾油器濾芯采用不銹鋼網，便于經常拆換清洗；精濾油器濾芯采用復合濾材，起始阻力小，通流面積大，保持較長時間不堵塞；

4.用戶也可根據需要，定作不同精度的濾芯，均適用于本濾油車．

、

(七、使用與維護) USAGE AND MAINTENANCE

1、濾油車啟動前應點動電機按鈕,確認油泵轉向符合濾油車上箭頭方向后，方可啟動工作。

2、首次使用時，應將油路中空氣排出，以免影響過濾效果。排氣方法:將精過濾器蓋上的放氣螺帽(見外形圖)松開2-4圈，待排完空氣有油液溢出時將其擰緊，再次使用若發現有空氣仍按上述方法排氣。

3、濾油車在使用過程中，若發現噪聲增大，出油量減少等異常情況，其主要原因是吸油管路漏氣，吸油不通暢或吸油租濾芯被污染堵塞，此時應及時停車檢查吸油軟管和接頭配合是否有問隙，有間隙或松動會吸入空氣引起噪聲:軟管插入液面下深度不夠，最淺深度應保持大于4d(軟管通徑):吸油管端與油液容器的側壁或底面保持一定距離，以保證吸油通暢，吸油濾芯是否堵塞，應拆卸吸油過濾器簡體，取下濾芯清洗或更換,若是循環過濾，回油管端應插入液面下.

4、若發現精過濾器蓋上的壓力表表壓達到02Mpa時，則說明精濾芯堵塞，這時更換濾芯，如果未及時處理，表壓繼續上升，當超過0 4Mpa時，安全閥即自動開啟，這時出油量將會明顯減少，更換濾芯時，應卸下蓋板螺栓，取出濾芯。

5、表壓上升過程中，突然產生壓力下降，則應檢查精濾芯是否被擊穿或油泵吸空。軟管應保持清潔，不使用時應及時將軟管口蓋封，將軟管盤卷掛在簡體的吊鉤上,注意不得擠扇軟管。

1. The oil car should anser some move electicel machinerypress and spain befare sta ting And we can start after confiming the tr ning of the oil pump is ac cording withthedrain ail ca.

2. While uringfor the frt time, should enpty the air in the oil passagf. s留not to influence the result of filtering Method of eshausting Release the 8ney spral xhel and 1ia of the pecise fiter covet to 2-4 brttons, to tghtenit while finishing exhaustng end the ail oveflovwing Use the sane methodwhile you findthereis silll air init.

3. If you find the noise increases andl the producing oil amnount redhucingin the course of using the ail ca, the most impart reason is the oil header pipelineleak gas suck ail not pugative a the core of the prede aner is stopped up th ckly by polution You hould stop your Cm end check if there is pace bebwet the tuibe of the ail header and the tie-in asoatif there is space betwe en them, itwill suck al and 810noise. if the depth of the liquid is not enough that the hose insat in, you shou dkeep the dh anetet bigger than 4dThe oil header end and ail container should keep a distanceto enmure suck al thorough If the core of the oil he ader is stopped, you shouldremove it and dea ar replace the core.You shouldinsert the retun tuibe under the lid, ifit is loop fltrate

4. If find the presaure of the extr act flter achieve 02Mpa it means the filter has stopped, andlyou should change the core. If you do not deal with it in time ,the presure will keep uprising,whan it exceed0. 4Mpa rlief valve will tun on aut omuatic. At this mament, the amount of the ail-out will reduce，You shouldr amove the cover plate bolt andtalke ou the corewhen you change the core.

5. If you find the presmure coming down suddenly duing the couse aof the presure gmige niaing you shouldl check: if the core of the extract flter is beat through ar the ail pumpis empty. The tube shoiuld ke ep clean ,and should cover the mouth of the tube & langit while d not use it try not to etrude it inflat.

LUC-16*3,LUC-16*5,LUC-16*10,LUC-16*20濾油車

LUCA-100*3,LUC-16*30,LUC-40*3,LUC-40*5福力德濾油車

LUC-40*10,LUCA-100*5,LUC-40*20,LUC-40*30濾油車生產廠家

LUC-63*3,LUC-63*5,LUCA-100*10,LUC-63*10精細濾油小車

LUC-63*20,LUC-63*30,LUC-100*3,LUCA-100*20濾油車生產廠家

LUC-100*5,LUC-100*10,LUC-100*20,LUC-100*30濾油車

LUCA-100*30,LUCA-16*3,LUCA-16*5,LUCA-16*10精細濾油小車

LUCA-16*20,LUCB-16*3,LUCA-16*30,LUCA-40*3福力德濾油車

LUCA-40*5,LUCA-40*10,LUCB-16*5,LUCA-40*20精細濾油小車