公路防撞墻模板 現澆鋼模板 加工制作

防撞墻模板在生產技術和產品原料上都有十分嚴格的要求，利昌模具工廠選擇硬度更高、在使用過程中更耐高溫不易變形的鋼材，再使用先進的技術進行彎曲、裁切和打磨，表面光滑美觀、實用性好，只要按照說明規范使用并在使用后及時做好清潔和保護，可以長期使用。公路護欄模具的具體使用規范如下：1.模具底部和頂部都沒有鋼板，由數根拉桿連接而成，用于現澆生產，一旦澆筑混凝土就無法再次移動，所以使用前必須把模具放到合適的位置然后刷上機油；2.調節公路護欄模具的拉桿使模具的寬度保持一致，擰緊相鄰模具間的螺栓，檢查各節模具間沒有留有縫隙，否則一旦漏漿會影響公路護欄質量；3.使用管道將攪拌好的混凝土注入模具，并使用振動棒將氣泡震出，然后給灌完漿的模具覆上一層塑料薄膜，來保證公路護欄的耐用和美觀；4.8個小時后揭去塑料薄膜，打開模具左右端的螺栓，拆去模具，然后等待混凝土護欄自然風干即可，拆下來的模具就可以進行下一段公路護欄的澆筑了。

The anti-collision wall formwork has very strict requirements on production technology and product raw materials. Lichang mould factory selects steel with higher hardness and higher temperature resistance and not easy to deform in the use process, and then uses advanced technology to bend, cut and polish. The surface is smooth, beautiful and practical. As long as it is used in accordance with the specification and cleaned and protected in time after use, it can grow Period of use. The specific use specifications of highway guardrail mold are as follows: 1. There is no steel plate at the bottom and top of the mold, which is connected by several pull rods and used for cast-in-place production. Once the concrete is poured, it cannot be moved again, so before use, the mold must be placed in a proper position and then painted with engine oil; 2. Adjust the pull rods of highway guardrail mold to keep the width of the mold consistent, and tighten the adjacent molds Bolt, check that there is no gap between the molds of each section, otherwise the leakage of slurry will affect the quality of highway guardrail; 3. Use the pipe to inject the mixed concrete into the mold, and use the vibrator to shake out the bubbles, and then cover the poured mold with a layer of plastic film to ensure the durability and beauty of highway guardrail; 4.8 hours later, remove the plastic film, open the bolts at the left and right ends of the mold Bolt, remove the mold, and then wait for the natural air drying of the concrete guardrail. The removed mold can be used for the next section of highway guardrail pouring.

防撞墻模板是根據當前在不同路段要求設計的圖紙加工的，因為在公路、橋上等使用的防撞護欄形狀以及尺寸都是不同的，所以模板在加工的時候也會按照具體施工圖進行。通過對山東防撞護欄模板的使用情況總結，大部分都是以高度在80-110厘米的為主，而且主要是在橋上使用，所以為了搬運方便，長度往往設置為一米一節，這樣做的話可以確保模板使用方便性，工人在搬運以及安裝的時候都會非常方便的。從防撞護欄模板的使用情況來看，大部分都是定制在30-50m就夠用了。防撞墻模板是在高速公路和橋梁上使用的一種模具產品，而且利用這種模具都是采用現場澆筑的生產形式，這種模具的長度一般都在兩米之內，所以在進行幾百米的防撞護欄的制作的時候，我們需要的防撞護欄鋼模具數量是很多的，具體的數量還是要根據工程的進度來具體考慮。

The anti-collision wall formwork is processed according to the drawings designed in different road sections at present. Because the shape and size of the anti-collision guardrail used in roads, bridges, etc. are different, the formwork will also be processed according to the specific construction drawings. Through the summary of the use of the formwork of the anti-collision guardrail in Shandong Province, most of them are mainly 80-110cm high and mainly used on the bridge, so in order to facilitate the handling, the length is often set as one meter section, which can ensure the convenience of the formwork use, and the workers will be very convenient in the handling and installation. From the perspective of the use of anti-collision guardrail templates, most of them are customized at 30-50m. The anti-collision wall formwork is a kind of mold product used on highways and bridges, and the use of this kind of mold is the production form of cast-in-place, the length of this kind of mold is generally within two meters, so when making the anti-collision guardrail of several hundred meters, we need a lot of anti-collision guardrail steel mold, the specific quantity should be based on the progress of the project Consider it in detail.